This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
products:sbc:vim1:hardware:interfaces [2022/07/13 22:01] frank |
products:sbc:vim1:hardware:interfaces [2023/03/22 04:01] nick [Table] |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== VIM1 Interfaces ====== | ====== VIM1 Interfaces ====== | ||
- | {{/ | + | ===== Top Side ===== |
- | {{/ | + | |
- | {{ / | + | |
- | <tabbox Front(Blue)> | + | {{products: |
- | | ^ Component | + | |
- | |1|USB-A|USB 2.0 speed, 500mA max output| | + | |
- | |2|RJ-45|10/100 Mbps Ethernet| | + | |
- | |3|HDMI|HDMI 2.0b with 3D, HDR, CEC and HDCP 2.2| | + | |
- | |4|USB-C|USB 2.0 OTG and 5V power input, can be used for upgrading the OS| | + | |
- | |5|USB-A|USB 2.0 speed, 900mA max output| | + | |
- | |6|Fan Header|4-wire fan header utilising pulse width modulation| | + | |
- | |7|Reset Button|Force reboot your VIM1 in the event of a system freeze| | + | |
- | |8|Function Button|Press this 3 times in 2 seconds to enter MaskROM mode| | + | |
- | |9|Power Button|This button turns on your VIM1| | + | |
- | |A|M2x4 Mounting Point|For mounting to cases and heatsinks| | + | |
- | |B|RTC Battery Header|Header for attaching a battery for the real time clock| | + | |
- | |C|40-Pin GPIO|Learn how to access the GPIO from here, or use it to add a Toneboard| | + | |
- | |D|Infrared Module|2-channel infrared receiver for use with Khadas IR remote| | + | |
- | |E|LEDs|Status indicator LEDs| | + | |
- | |F|I-Pex Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector| | + | |
- | <tabbox Back(Red)> | + | |
+ | | ^ Component | ||
+ | | 1 | USB-A | USB 2.0 speed, 500mA max output | ||
+ | | 2 | RJ-45 | 10/100 Mbps Ethernet | ||
+ | | 3 | HDMI | HDMI 2.0b output with 3D, HDR, CEC and HDCP 2.2 | | ||
+ | | 4 | USB-C | USB 2.0 OTG and 5V power input, can be used for upgrading the OS | | ||
+ | | 5 | USB-A | USB 2.0 speed, 900mA max output | ||
+ | | 6 | Fan Header | ||
+ | | 7 | Reset Button | ||
+ | | 8 | Function Button | ||
+ | | 9 | Power Button | ||
+ | | A | RTC Battery Header | ||
+ | | B | M2x4 Mounting Point | For mounting to cases and heatsinks | ||
+ | | C | 40-Pin GPIO | Learn how to access the GPIO from here, or use it to add a Toneboard | ||
+ | | D | Infrared Module | ||
+ | | E | LEDs | Status indicator LEDs | | ||
+ | | F | I-Pex Wi-Fi / Bluetooth Connector | ||
+ | |||
+ | ===== Back Sise ===== | ||
+ | |||
+ | {{products: | ||
Line 33: | Line 35: | ||
- | <tabbox Buttons> | + | ===== Hardware buttons ===== |
- | + | ||
- | ^ Reset ^ Function | + | |
- | |x| | |Force Reboot VIM1| | + | |
- | | |x| |Enter Upgrade Mode (TST)| | + | |
- | | | |x|Power On/Wake Up VIM1| | + | |
- | |x| |x|Enter Upgrade Mode (KEYS)| | + | |
- | |x|x|x|Erase EMMC| | + | |
- | <tabbox Indicator LEDs> | + | {{products: |
- | ^ Colour | ||
- | |Blue|OFF|Power source disconnected| | ||
- | | |Solid ON|Power source connected, SBC turned off| | ||
- | |White|OFF|SBC turned off| | ||
- | | |Solid ON|SBC turned on| | ||
- | |Red|None|None| | ||
+ | ^ Reset ^ Function | ||
+ | | x | | | Force Reboot VIM1 | | ||
+ | | | ||
+ | | | ||
+ | | x | | x | Enter Upgrade Mode (KEY) | | ||
- | <WRAP important > | ||
- | The above behaviours are default out-of-the-box, | ||
- | </ | ||
- | < | + | ===== GPIO header pinout ===== |
{{products: | {{products: | ||
- | </ |