This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
products:sbc:vim4:hardware:start [2022/07/04 21:20] nick [Indicator LEDs] |
products:sbc:vim4:hardware:start [2022/09/28 09:17] nick |
||
---|---|---|---|
Line 2: | Line 2: | ||
- | ====== Hardware ====== | + | ====== |
- | ===== Interfaces | + | /* |
+ | Please check [[products: | ||
+ | */ | ||
- | {{:products: | + | {{page>products: |
- | {{: | + | ===== Schematics & Drawings ===== |
- | ===== Hardware Information ===== | + | * [[dl> |
+ | * [[dl> | ||
+ | * [[dl> | ||
- | {{: | + | ===== Datasheets ===== |
+ | * [[dl> | ||
- | <tabbox Front(Blue)> | + | ===== Misc ===== |
- | | ^ Component | + | * [[dl>products/vim4/specs/|Specs]] |
- | | 1 | USB-A | USB 3.0 port that supports 1500mA output | + | |
- | | 2 | RJ-45 | Gigabit LAN port that supports Wake-On-LAN | + | |
- | | 3 | HDMI Output | + | |
- | | 4 | USB-C | USB-C port with USB power delivery (9-20V input) and 2.0 speeds, can be used for upgrading the OS | | + | |
- | | 5 | USB-A | USB 2.0 port that supports 1300mA output | + | |
- | | 6 | Fan Header | + | |
- | | 7 | Reset Button | + | |
- | | 8 | Function Button | + | |
- | | 9 | Power Button | + | |
- | | A | RTC Header | + | |
- | | B | M2 Hole | M2 clearance holes for a case, or adding a heatsink | + | |
- | | C | 40-Pin GPIO | General input/ | + | |
- | | D | DMIC | Digital Microphone | + | |
- | | E | HDMI Input | Tpye-D HDMI input | | + | |
- | | F | LEDs | Indicator LEDs | | + | |
- | | G | MCU | STM32G0 micro-controller | + | |
- | | | + | |
- | | H | MHF4 Antenna | + | |
- | | I | MHF4 Antenna | + | |
- | | J | Current Limit Switch | + | |
- | + | ||
- | <tabbox Back(Red)> | + | |
- | + | ||
- | ^ ^ Component | + | |
- | | 1 | VIN | 9-20V power input | | + | |
- | | 2 | Micro-SD Slot | Molex Slot, spec version 2.x/3.x/4.x (SDSC/SDHC/ | + | |
- | | 3 | M.2 Slot | PCIe 2.0 (x1 lane), supports M.2 2280 NVMe SSDs | | + | |
- | | 4 | MIPI-CSI | + | |
- | | 5 | MIPI-CSI | + | |
- | | 6 | MIPI-DSI& | + | |
- | | 7 | V-by-One | + | |
- | | 8 | XPWR Pads | Connect an external power switch using these pads | | + | |
- | | 9 | SPI Flash | Flash memory module that interfaces over SPI | | + | |
- | | A | Current Limit Switch | + | |
- | | B | G-Sensor | + | |
- | + | ||
- | <tabbox Buttons> | + | |
- | + | ||
- | ^ Reset ^ Function | + | |
- | | x | + | |
- | | | x | | Enter Upgrade Mode (TST) | | + | |
- | | | | + | |
- | | | | + | |
- | + | ||
- | <tabbox Indicator LEDs> | + | |
- | ^ Colour | + | |
- | | Red | OFF | Power source disconnected | + | |
- | | | Solid ON | Power source connected, SBC turned off | | + | |
- | | White | OFF | SBC turned off | | + | |
- | | | Solid ON | SBC turned on | | + | |
- | + | ||
- | <WRAP tip > | + | |
- | The above behaviours are default out-of-the-box, | + | |
- | </WRAP> | + | |
- | + | ||
- | <WRAP important > | + | |
- | important box | + | |
- | </WRAP> | + | |
- | + | ||
- | + | ||
- | </tabbox> | + | |
- | + | ||
- | </ | + | |
- | + | ||
- | + | ||
- | ---- | + | |
- | + | ||
- | ===== Other ===== | + | |
- | + | ||
- | {{indexmenu> | + |