Differences

This shows you the differences between two versions of the page.

--- products:sbc:vim2:hardware:interfaces [2022/09/23 22:17]
nick [Table]
+++ products:sbc:vim2:hardware:interfaces [2023/03/22 04:00] (current)
nick
@@ Line 2: / Line 2: @@
-{{products:sbc:vim2:hardware:vim2-interface.jpg?1200}}
-{{products:sbc:vim2:hardware:vim2-labels.jpg?1200}}
+===== Top side =====
-<tabbox Front(Blue)>
+{{products:sbc:vim2:hardware:vim2-interfaces-top-side.webp?600}}
-|    ^ Component             ^ Purpose  ^
-|1|USB-A|USB 2.0 speed, 500mA max output|
-|2|RJ-45|Gigabit Ethernet with Wake-On-LAN (WOL)|
-|3|HDMI|HDMI 2.0a with CEC, 4K@60Hz|
-|4|USB-C|USB 2.0 OTG and 5V power input, can be used for upgrading the OS|
-|5|USB-A|USB 2.0 speed, 900mA max output|
-|6|Current Limit Switch|Prevents damage to VIM2 during uneven loading conditions|
-|7|Fan Header|4-wire fan header utilising pulse width modulation|
-|8|Reset Button|Force reboot your VIM2 in the event of a system freeze|
-|9|Function Button|Press this 3 times in 2 seconds to enter MaskROM mode|
-|A|Power Button|This button turns on your VIM2|
-|B|M2x4 Mounting Point|For mounting to cases and heatsinks|
-|C|RTC Battery Header|Header for attaching a battery for the real time clock|
-|D|40-Pin GPIO|Learn how to access the GPIO from here, or use it to add a Toneboard|
-|E|Infrared Module|2-channel infrared receiver for use with Khadas IR remote|
-|F|LEDs|Status indicator LEDs|
-|G|FPC Connector|10-pins, 0.5mm pitch, with I2C, IOs|
-|H|I-Pex Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector|
-|I|I-Pex Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector|
-<tabbox Back(Red)>
+|    ^ Component                          ^ Purpose                                                               ^
+| 1  | USB-A                              | USB 2.0 speed, 500mA max output                                       |
+| 2  | RJ-45                              | Gigabit Ethernet with Wake-On-LAN (WOL)                               |
+| 3  | HDMI                               | HDMI 2.0a output with CEC, 4K@60Hz                                    |
+| 4  | USB-C                              | USB 2.0 OTG and 5V power input, can be used for upgrading the OS      |
+| 5  | USB-A                              | USB 2.0 speed, 900mA max output                                       |
+| 6  | Current Limit Switch               | Prevents damage to VIM2 during uneven loading conditions              |
+| 7  | Fan Header                         | 4-wire fan header utilising pulse width modulation                    |
+| 8  | Reset Button                       | Force reboot your VIM2                                                |
+| 9  | Function Button                    | Press this 3 times in 2 seconds to enter MaskROM mode                 |
+| A  | Power Button                       | This button turns on your VIM2                                        |
+| B  | RTC Battery Header                 | Header for attaching a battery for the real time clock                |
+| C  | M2x4 Mounting Point                | For mounting to cases and heatsinks                                   |
+| D  | 40-Pin GPIO                        | Learn how to access the GPIO from here, or use it to add a Toneboard  |
+| E  | Infrared Module                    | 2-channel infrared receiver for use with Khadas IR remote             |
+| F  | LEDs                               | Status indicator LEDs                                                 |
+| G  | FPC Connector                      | 10-pins, 0.5mm pitch, with I2C, IOs                                   |
+| H  | I-Pex Wi-Fi / Bluetooth Connector  | Wi-Fi / BT Antenna connector                                          |
-|    ^ Component             ^ Purpose  ^
+===== Back side =====
-|1|Pogo Pads|External 5V power input, can be provided by vTV Board(DVB Tuner)|
-|2|Micro-SD Card Slot|Boot alternative OSes via a micro-SD card, or just for extra storage|
-|3|500mA Fuse|Fuse for the 500mA USB port|
-|4|WOL Switch|Power switch activated via Wake-On-LAN|
-|5[MCU|STM8S003 micro-controller with programmable EEPROM|
-|6|MCU Pogo Pads|SWIM, UART, ADC, NRST|
-|7|SPI Flash|Flash memory module that interfaces over SPI|
-|8|20-Pin Pogo Pads|USB, I2C, DVB-Bus, IOs, for docking with the vTV Board(DVB Tuner)|
-|9|XPWR Pads|Connect an external power switch using these pads|
-|A|900mA Fuse|Fuse for the 900mA USB port|
+{{products:sbc:vim2:hardware:vim2-interfaces-back-side.webp?600}}
-<tabbox Buttons>
-^  Reset  ^  Function  ^  Power  ^  Purpose                   ^
+|    ^ Component           ^ Purpose                                                               ^
-|  x      |            |         |                            |
+| 1  | Pogo Pads           | External 5V power input, can be provided by vTV Board(DVB Tuner)      |
-|         |  x         |         | Enter Upgrade Mode (TST)   |
+| 2  | Micro-SD Card Slot  | Boot alternative OSes via a micro-SD card, or just for extra storage  |
-|         |            |  x      | Power On/Wake Up VIM2      |
+| 3  | MCU                 | STM8S003 micro-controller with programmable EEPROM                    |
-|  x      |            |  x      | Enter Upgrade Mode (KEYS)  |
+| 4  | MCU Pogo Pads       | SWIM, UART, ADC, NRST                                                 |
+| 5  | M-Register          | Shortcut to mask the eMMC                                             |
+| 6  | SPI Flash           | Flash memory module that interfaces over SPI                          |
+| 7  | 20-Pin Pogo Pads    | USB, I2C, DVB-Bus, IOs, for docking with the vTV Board(DVB Tuner)     |
+| 8  | XPWR Pads           | Connect an external power switch using these pads                     |
+===== Hardware buttons =====
-<tabbox GPIO Pinout>
+{{products:sbc:vim2:hardware:vim2-buttons.webp?400}}
+^  Reset  ^  Function  ^  Power  ^  Purpose                             ^
+|  x      |            |         | Force Reboot VIM2                    |
+|         |  x         |         | Enter Upgrade Mode (TST) (V14 only)  |
+|         |            |  x      | Power On/Wake Up VIM2                |
+|  x      |            |  x      | Enter Upgrade Mode (KEYS)            |
+Special button shortcuts
+  * Press ''FUNCTION'' 3 times in 2 seconds to enter MaskROM mode. (V14 only)
+===== GPIO header pinout =====
 ^SIGNAL ^PIN ^PIN ^SIGNAL ^
@@ Line 77: / Line 83: @@
 |3.3V|20|40|GND|
-</tabbox>

Khadas Docs

User Tools

Site Tools

Differences

Page Tools