User Tools
products:sbc:vim2:hardware:interfaces
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
products:sbc:vim2:hardware:interfaces [2023/03/22 03:11] nick |
products:sbc:vim2:hardware:interfaces [2023/03/22 03:22] nick [Hardware buttons] |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| - | | ^ Component | + | | ^ Component |
| - | |1|USB-A|USB 2.0 speed, 500mA max output| | + | | 1 | USB-A | USB 2.0 speed, 500mA max output |
| - | |2|RJ-45|Gigabit Ethernet with Wake-On-LAN (WOL)| | + | | 2 | RJ-45 | Gigabit Ethernet with Wake-On-LAN (WOL) |
| - | |3|HDMI|HDMI 2.0a with CEC, 4K@60Hz| | + | | 3 | HDMI |
| - | |4|USB-C|USB 2.0 OTG and 5V power input, can be used for upgrading the OS| | + | | 4 | USB-C | USB 2.0 OTG and 5V power input, can be used for upgrading the OS | |
| - | |5|USB-A|USB 2.0 speed, 900mA max output| | + | | 5 | USB-A | USB 2.0 speed, 900mA max output |
| - | |6|Current Limit Switch|Prevents damage to VIM2 during uneven loading conditions| | + | | 6 | Current Limit Switch |
| - | |7|Fan Header|4-wire fan header utilising pulse width modulation| | + | | 7 | Fan Header |
| - | |8|Reset Button|Force reboot your VIM2 in the event of a system freeze| | + | | 8 | Reset Button |
| - | |9|Function Button|Press this 3 times in 2 seconds to enter MaskROM mode| | + | | 9 | Function Button |
| - | |A|Power Button|This button turns on your VIM2| | + | | A | Power Button |
| - | |B|M2x4 Mounting Point|For mounting to cases and heatsinks| | + | | B | RTC Battery Header |
| - | |C|RTC Battery Header|Header for attaching a battery for the real time clock| | + | | C | M2x4 Mounting Point | For mounting to cases and heatsinks |
| - | |D|40-Pin GPIO|Learn how to access the GPIO from here, or use it to add a Toneboard| | + | | D | 40-Pin GPIO | Learn how to access the GPIO from here, or use it to add a Toneboard |
| - | |E|Infrared Module|2-channel infrared receiver for use with Khadas IR remote| | + | | E | Infrared Module |
| - | |F|LEDs|Status indicator LEDs| | + | | F | LEDs |
| - | |G|FPC Connector|10-pins, | + | | G | FPC Connector |
| - | |H|I-Pex Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector| | + | | H | I-Pex Wi-Fi / Bluetooth Connector |
| - | |I|I-Pex Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector| | + | |
| Line 34: | Line 33: | ||
| - | | ^ Component | + | | ^ Component |
| - | |1|Pogo Pads|External 5V power input, can be provided by vTV Board(DVB Tuner)| | + | | 1 | Pogo Pads |
| - | |2|Micro-SD Card Slot|Boot alternative OSes via a micro-SD card, or just for extra storage| | + | | 2 | Micro-SD Card Slot | Boot alternative OSes via a micro-SD card, or just for extra storage |
| - | |3|500mA Fuse|Fuse for the 500mA USB port| | + | | 3 | MCU |
| - | |4|WOL Switch|Power switch activated via Wake-On-LAN| | + | | 4 |
| - | |5|MCU|STM8S003 micro-controller with programmable EEPROM| | + | | 5 | M-Register |
| - | |6|MCU Pogo Pads|SWIM, UART, ADC, NRST| | + | | 6 |
| - | |7|SPI Flash|Flash memory module that interfaces over SPI| | + | | 7 |
| - | |8|20-Pin Pogo Pads|USB, I2C, DVB-Bus, IOs, for docking with the vTV Board(DVB Tuner)| | + | | 8 |
| - | |9|XPWR Pads|Connect an external power switch using these pads| | + | |
| - | |A|900mA Fuse|Fuse for the 900mA USB port| | + | |
| ===== Hardware buttons ===== | ===== Hardware buttons ===== | ||
| Line 51: | Line 48: | ||
| - | ^ Reset ^ Function | + | ^ Reset ^ Function |
| - | | x | | | + | | x | | |
| - | | | + | | |
| - | | | + | | |
| - | | x | | x | Enter Upgrade Mode (KEYS) | + | | x | | x | Enter Upgrade Mode (KEYS) |
| Special button shortcuts | Special button shortcuts | ||
| - | * Press '' | + | * Press '' |
| ===== GPIO header pinout ===== | ===== GPIO header pinout ===== | ||
Last modified: 2023/03/22 04:00 by nick