This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
products:sbc:vim2:hardware:interfaces [2022/09/05 23:34] frank |
products:sbc:vim2:hardware:interfaces [2023/03/22 03:11] nick |
||
---|---|---|---|
Line 2: | Line 2: | ||
- | {{products: | ||
- | {{/products: | + | ===== Top side ===== |
+ | |||
+ | {{products: | ||
- | <tabbox Front(Blue)> | ||
| ^ Component | | ^ Component | ||
|1|USB-A|USB 2.0 speed, 500mA max output| | |1|USB-A|USB 2.0 speed, 500mA max output| | ||
Line 28: | Line 29: | ||
- | < | + | ===== Back side ===== |
+ | |||
+ | {{products: | ||
Line 36: | Line 39: | ||
|3|500mA Fuse|Fuse for the 500mA USB port| | |3|500mA Fuse|Fuse for the 500mA USB port| | ||
|4|WOL Switch|Power switch activated via Wake-On-LAN| | |4|WOL Switch|Power switch activated via Wake-On-LAN| | ||
- | |5[MCU|STM8S003 micro-controller with programmable EEPROM| | + | |5|MCU|STM8S003 micro-controller with programmable EEPROM| |
|6|MCU Pogo Pads|SWIM, UART, ADC, NRST| | |6|MCU Pogo Pads|SWIM, UART, ADC, NRST| | ||
|7|SPI Flash|Flash memory module that interfaces over SPI| | |7|SPI Flash|Flash memory module that interfaces over SPI| | ||
Line 43: | Line 46: | ||
|A|900mA Fuse|Fuse for the 900mA USB port| | |A|900mA Fuse|Fuse for the 900mA USB port| | ||
+ | ===== Hardware buttons ===== | ||
- | <tabbox Buttons> | + | {{products: |
- | ^ Reset ^ Function | ||
- | |x| | |Force Reboot VIM2 | ||
- | | |x| |Enter Upgrade Mode (TST)| | ||
- | | | |x|Power On/Wake Up VIM2| | ||
- | |x| |x|Enter Upgrade Mode (KEYS)| | ||
- | |x|x|x|Erase EMMC| | ||
+ | ^ Reset ^ Function | ||
+ | | x | | | ||
+ | | | ||
+ | | | ||
+ | | x | | x | Enter Upgrade Mode (KEYS) | ||
- | <tabbox Indicator LEDs> | + | Special button shortcuts |
- | ^ Colour | + | * Press '' |
- | |Blue|OFF|Power source disconnected| | + | |
- | | |Solid ON|Power source connected, SBC turned off| | + | |
- | |White|OFF|SBC turned off| | + | |
- | | |Solid ON|SBC turned on| | + | |
- | |Red|None|None| | + | |
- | + | ===== GPIO header pinout ===== | |
- | + | ||
- | <WRAP important > | + | |
- | The above behaviours are default out-of-the-box, | + | |
- | </ | + | |
- | + | ||
- | < | + | |
^SIGNAL ^PIN ^PIN ^SIGNAL ^ | ^SIGNAL ^PIN ^PIN ^SIGNAL ^ | ||
Line 94: | Line 86: | ||
|3.3V|20|40|GND| | |3.3V|20|40|GND| | ||
- | </ | + |