User Tools
products:sbc:vim2:hardware:interfaces
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
products:sbc:vim2:hardware:interfaces [2022/09/05 23:34] frank |
products:sbc:vim2:hardware:interfaces [2023/02/04 01:16] hyphop |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| - | {{products: | + | {{products: |
| - | {{/products: | + | {{products: |
| + | |||
| + | ===== Top side ===== | ||
| - | <tabbox Front(Blue)> | ||
| | ^ Component | | ^ Component | ||
| |1|USB-A|USB 2.0 speed, 500mA max output| | |1|USB-A|USB 2.0 speed, 500mA max output| | ||
| Line 28: | Line 29: | ||
| - | < | + | ===== Back side ===== |
| Line 36: | Line 37: | ||
| |3|500mA Fuse|Fuse for the 500mA USB port| | |3|500mA Fuse|Fuse for the 500mA USB port| | ||
| |4|WOL Switch|Power switch activated via Wake-On-LAN| | |4|WOL Switch|Power switch activated via Wake-On-LAN| | ||
| - | |5[MCU|STM8S003 micro-controller with programmable EEPROM| | + | |5|MCU|STM8S003 micro-controller with programmable EEPROM| |
| |6|MCU Pogo Pads|SWIM, UART, ADC, NRST| | |6|MCU Pogo Pads|SWIM, UART, ADC, NRST| | ||
| |7|SPI Flash|Flash memory module that interfaces over SPI| | |7|SPI Flash|Flash memory module that interfaces over SPI| | ||
| Line 43: | Line 44: | ||
| |A|900mA Fuse|Fuse for the 900mA USB port| | |A|900mA Fuse|Fuse for the 900mA USB port| | ||
| + | ===== Hardware buttons ===== | ||
| - | <tabbox Buttons> | ||
| - | ^ Reset ^ Function | + | ^ Reset ^ Function |
| - | |x| | |Force Reboot VIM2 | + | | x | | | |
| - | | |x| |Enter Upgrade Mode (TST)| | + | | |
| - | | | |x|Power On/Wake Up VIM2| | + | | |
| - | |x| |x|Enter Upgrade Mode (KEYS)| | + | | x | | x | Enter Upgrade Mode (KEYS) |
| - | |x|x|x|Erase EMMC| | + | |
| + | Special button shortcuts | ||
| - | <tabbox Indicator LEDs> | + | * Press '' |
| - | ^ Colour | + | ===== GPIO header pinout ===== |
| - | |Blue|OFF|Power source disconnected| | + | |
| - | | |Solid ON|Power source connected, SBC turned off| | + | |
| - | |White|OFF|SBC turned off| | + | |
| - | | |Solid ON|SBC turned on| | + | |
| - | |Red|None|None| | + | |
| - | + | ||
| - | + | ||
| - | + | ||
| - | <WRAP important > | + | |
| - | The above behaviours are default out-of-the-box, | + | |
| - | </ | + | |
| - | + | ||
| - | < | + | |
| ^SIGNAL ^PIN ^PIN ^SIGNAL ^ | ^SIGNAL ^PIN ^PIN ^SIGNAL ^ | ||
| Line 94: | Line 82: | ||
| |3.3V|20|40|GND| | |3.3V|20|40|GND| | ||
| - | </ | + | |
Last modified: 2023/03/22 04:00 by nick