This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
products:sbc:edge1:hardware:interfaces [2022/09/05 23:41] frank |
products:sbc:edge1:hardware:interfaces [2023/03/22 03:52] nick [Table] |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== Edge1 Interfaces ====== | ====== Edge1 Interfaces ====== | ||
- | {{products: | + | ===== Top Side ===== |
- | {{/products/sbc/edge1/hardware/docs-edge-v-labels.jpg?1200}} | + | {{products:sbc:edge1:hardware:edge1-interfaces-top-side.webp?600}} |
- | <tabbox Front(Blue)> | ||
- | | ^ Component | ||
- | |1|USB-A|USB 3.0, blue colour| | ||
- | |2|RJ-45|Gigabit Ethernet with Wake-On-LAN (WOL)| | ||
- | |3|HDMI|Type-A Female, up to 4K@60Hz, HDCP 2.2| | ||
- | |4|USB-C|USB 3.0, Display Port v1.2, can be used for upgrading the OS| | ||
- | |5|USB-A|USB 2.0, black colour| | ||
- | |6|Fan Header|4-wire fan header utilising pulse width modulation| | ||
- | |7|Reset Button|Force reboot your Edge-V in the event of a system freeze| | ||
- | |8|Function Button|Press this 3 times in 2 seconds to enter MaskROM mode| | ||
- | |9|Power Button|This button turns on your Edge-V| | ||
- | |A|RTC Battery Header|Header for attaching a battery for the real time clock| | ||
- | |B|40-Pin GPIO|access GPIO, or use it to add a Toneboard| | ||
- | |C|Gesture Sensor|Control your Edge-V with a hand-wave| | ||
- | |D|Infrared Module|2-channel infrared receiver for use with Khadas IR remote| | ||
- | |E|LEDs|Status indicator LEDs| | ||
- | |F|I-Pex Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector| | ||
- | |G|I-Pex Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector| | ||
+ | | ^ Component | ||
+ | | 1 | USB-A | USB 3.0, blue colour | ||
+ | | 2 | RJ-45 | Gigabit Ethernet with Wake-On-LAN (WOL) | | ||
+ | | 3 | HDMI | Type-A Female, up to 4K@60Hz, HDCP 2.2 | | ||
+ | | 4 | USB-C | USB 3.0, Display Port v1.2, can be used for upgrading the OS | | ||
+ | | 5 | USB-A | USB 2.0, black colour | ||
+ | | 6 | Fan Header | ||
+ | | 7 | Reset Button | ||
+ | | 8 | Function Button | ||
+ | | 9 | Power Button | ||
+ | | A | RTC Battery Header | ||
+ | | B | M2 Hole | M2 clearance holes for a case, or adding a heatsink | ||
+ | | C | 40-Pin GPIO | access GPIO, or use it to add a Toneboard | ||
+ | | D | Gesture Sensor | ||
+ | | E | Infrared Module | ||
+ | | F | LEDs | Status indicator LEDs | | ||
+ | | G | I-Pex Wi-Fi / Bluetooth Connector | ||
- | <tabbox Back(Red)> | ||
+ | ===== Back Side ===== | ||
- | | ^ Component | + | {{products:sbc: |
- | |1|Li-Po Battery Connector|Connect a Lithium Polymer battery with the [Juice Board](https:// | + | |
- | |2|USB-C|USB-C port that accepts 5-20V power input (USB power delivery)| | + | |
- | |3|Micro-SD Card Slot|Boot alternative OSes via a Micro-SD card, or just for extra storage| | + | |
- | |4|M.2 Socket (PCI-E 2.1)|Connect 2280 NVMe SSDS at 4-lane speed with M2X Extension| | + | |
- | |5|E-DP Display|For connecting to external displays via E-DP| | + | |
- | |6|M2x4 Mounting Point|For mounting to cases and heatsinks| | + | |
- | |7|Touch Panel|For accepting touch-input| | + | |
- | |8|MIPI-TX|MIPI-DSI header for connecting LCD screens| | + | |
- | |9|MIPI-RX|For connecting to MIPI-CSI cameras| | + | |
- | |A|MIPI-RX/ | + | |
- | |B|M-Register|Another way for entering upgrade mode| | + | |
- | <tabbox Buttons> | + | | ^ Component |
+ | | 1 | USB-C | USB-C port that accepts 5-20V power input (PD only) | | ||
+ | | 2 | Micro-SD Card Slot | Boot alternative OSes via a Micro-SD card, or just for extra storage | ||
+ | | 3 | M.2 Socket (PCI-E 2.1) | Connect 2280 NVMe SSDS at 4-lane speed with M2X Extension | ||
+ | | 4 | E-DP Display | ||
+ | | 5 | Touch Panel | For accepting touch-input | ||
+ | | 6 | MIPI-DSI | ||
+ | | 7 | MIPI-CSI | ||
+ | | 8 | MIPI-CSI | ||
+ | | 9 | M-Register | ||
+ | | A | Li-Po Battery Connector | ||
- | ^ Reset ^ Function | ||
- | |x| | |Force Reboot Edge-V| | ||
- | | |x| |Enter Upgrade Mode (TST)| | ||
- | | | |x|Power On/Wake Up Edge-V| | ||
- | |x| |x|Enter Upgrade Mode (KEYS)| | ||
+ | ===== Hardware buttons ===== | ||
- | <tabbox Indicator LEDs> | + | {{products: |
- | ^ Colour | ||
- | |Blue|OFF|Power source disconnected| | ||
- | | |Solid ON|Power source connected, SBC turned off| | ||
- | |White|OFF|SBC turned off| | ||
- | | |Solid ON|SBC turned on| | ||
- | |Red|None|None| | ||
+ | ^ Reset ^ Function | ||
+ | | x | | | Force Reboot Edge-V | ||
+ | | | ||
+ | | | ||
+ | | x | | x | Enter Upgrade Mode (KEYS) | ||
- | <WRAP important > | ||
- | The above behaviours are default out-of-the-box, | ||
- | </ | ||
- | < | + | ===== GPIO header pinout ===== |
^SIGNAL | ^SIGNAL | ||
Line 89: | Line 79: | ||
|Linux_TX|19|39|MCU_PA1| | |Linux_TX|19|39|MCU_PA1| | ||
|3.3V|20|40|GND| | |3.3V|20|40|GND| | ||
+ | |||
+ | [[../ | ||
+ | |||
</ | </ |