This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
software:oowow:user-manual [2022/10/18 23:47] hyphop [Security and Privacy] |
software:oowow:user-manual [2022/12/28 02:55] hyphop [Common Button Shortcuts] |
||
---|---|---|---|
Line 36: | Line 36: | ||
* Accept Hotspot client | * Accept Hotspot client | ||
* Power off - Long press the **POWER** button until device shuts down | * Power off - Long press the **POWER** button until device shuts down | ||
- | * Enter multifunction mode - press and hold **FUNCTION** button (loop cycle: Hotspot -> Firewall Allow -> Firewall Block -> Cancel, each mode wait 2 sec ), release to activate selected function | + | * Enter multifunction mode - press and hold **FUNCTION** button (loop cycle: |
<WRAP tip > | <WRAP tip > | ||
Line 110: | Line 110: | ||
<WRAP tip > | <WRAP tip > | ||
- | Access can be restricted by the Firewall. | + | Access can be restricted by the [[# |
</ | </ | ||
Line 143: | Line 143: | ||
==== WEB API ==== | ==== WEB API ==== | ||
- | For developers and advanced users only. WIP: | + | For developers and advanced users WIP: |
+ | |||
+ | <WRAP tip > | ||
+ | Access can be restricted by the [[# | ||
+ | </ | ||
+ | |||
+ | |||
+ | ==== Dump eMMC by usb network ==== | ||
+ | |||
+ | ``` | ||
+ | curl -L 172.22.1.1/ | ||
+ | ``` | ||
+ | |||
+ | ==== Dump eMMC by LAN network ==== | ||
+ | |||
+ | ``` | ||
+ | curl -L OOWOW_HOST_NAME_OR_IP/ | ||
+ | ``` | ||
+ | |||
+ | ==== Write SPI oowow image by LAN network ==== | ||
+ | |||
+ | |||
+ | ```sh Write or update SPI-flash firmware by LAN | ||
+ | |||
+ | curl OOWOW_HOST_NAME_OR_IP/ | ||
+ | ``` | ||
+ | |||
+ | ==== Write SPI oowow image by USB-otg network ==== | ||
+ | |||
+ | ```sh Write or update SPI-flash firmware by USB-otg network | ||
+ | curl 172.22.1.1/ | ||
+ | ``` | ||
===== Networks ===== | ===== Networks ===== | ||
Line 339: | Line 370: | ||
===== Device configure KBI ===== | ===== Device configure KBI ===== | ||
+ | // Main menu => Device configure KBI // | ||
- | main menu -> Device configure KBI | + | KBI is an abbreviation for Khadas Bootloader Instructions, |
+ | developed to fulfill the following purposes: | ||
+ | |||
+ | * Manage the programmable MCU | ||
+ | * Carry out low level hardware management | ||
+ | * Let developers utilize all the features of SBC device | ||
+ | |||
+ | ==== Reset MCU to factory mode ==== | ||
+ | |||
+ | Reset MCU/KBI configuration to default values | ||
+ | |||
+ | <WRAP tip > | ||
+ | This procedure totally safe, and never change eMMC storage content or any other parts. | ||
+ | </ | ||
+ | |||
+ | ==== Boot-mode ==== | ||
+ | |||
+ | Setup device boot-mode values: | ||
+ | |||
+ | * '' | ||
+ | * '' | ||
+ | |||
+ | <WRAP important > | ||
+ | For use Android need setup boot-mode to '' | ||
+ | </WRAP> | ||
WIP: | WIP: | ||
Line 350: | Line 406: | ||
* OOWOW works only by user demand, and never works in the background | * OOWOW works only by user demand, and never works in the background | ||
* OOWOW never sends any private data from your device to the internet | * OOWOW never sends any private data from your device to the internet | ||
- | * By default, remote access to your device is blocked by the firewall | + | * By default, remote access to your device is blocked by the [[#firewall]] |
===== Limitations ===== | ===== Limitations ===== |