Differences

This shows you the differences between two versions of the page.

--- products:sbc:vim4:development:boot-sequence [2022/07/26 02:29]
hyphop [VIM4 OS Boot Priority]
+++ products:sbc:vim4:development:boot-sequence [2022/08/22 03:33] (current)
hyphop old revision restored (2022/08/22 14:54)
@@ Line 1: / Line 1: @@
+~~tag>VIM4 boot-sequence MCU~~
 ====== VIM4 OS Boot Priority ======
-VIM4 is capable of booting from the following devices: ''eMMC'',  ''TF Card'', ''SPI Flash''
+VIM4 have possibility boot-up from : ''eMMC'', ''TF Card'', ''SPI-Flash''
 <WRAP info >
-We talking there only about 1st stage SOC boot, next second stage os loading possible for any other diveices like USB storages, NVME etc ...
+We talking there only about 1st stage SoC boot,
+next second stage OS loading possible for any other devices like USB storage's,
+NVMe etc ... and depends from ''u-boot'' configurations
 </WRAP>
-/* not sure its needed ?
-The OS image can be flased into the ''eMMC'', ''TF Card'' or ''SPI Flash''.
-*/
 ===== Default boot priority =====
-  - TF Card
+  - TF-Card <wrap important>always highest priority</wrap>
   - eMMC
-  - SPI Flash
+  - SPI-Flash
+===== U-Boot shell usage =====
+You can change the boot priority of the ''eMMC'' and ''SPI-Flash'' via the [[products:sbc:vim4:development:kbi|KBI(Khadas Boot Instructions)]] from u-boot shell
+Change boot priority to: ''TF-Card'' => ''eMMC'' => ''SPI-Flash''
+```shell
+kvim4# kbi bootmode w emmc
+```
+Change boot priority to: ''TF-Card'' => ''SPI-Flash'' => ''eMMC''
+```shell
+kvim4# kbi bootmode w spi
+```
 <WRAP important >
-''TF Card'' will always take the highest priority.
+for apply setting for next boot, need reboot device by ''RESET'' button or re-plug power cable or power-off device or [[#hot-apply-setting-changes-via-mcu-reboot|reboot via mcu]]
 </WRAP>
-You can also swap the boot priority of the ''eMMC'' and ''SPI Flash'' via the [[products:sbc:vim4:development:kbi|KBI(Khadas Boot Instructions)]], but the ''TF Card'' will always take the highest priority.
+===== Linux command-line usage =====
-  * Setting the priority of ''eMMC'' above ''SPI Flash''
+```sh
+i2cset -f -y 6 0x18 0x20 1 # setup default eMMC boot-mode
+```
-```shell
+```sh
-kvim4# kbi bootmode w emmc
+i2cset -f -y 6 0x18 0x20 0 # setup SPI-flash boot-mode
 ```
-Then the boot priority will become:
+==== Hot apply setting changes via mcu reboot ====
-  - TF Card
+```sh
-  - eMMC
+i2cset -f -y 6 0x18 0x91 1
-  - SPI Flash
+```
-  * Setting the priority of ''SPI Flash'' above ''eMMC''
-```shell
+===== OOWOW boot special shortcut =====
-kvim4# kbi bootmode w spi
-```
+Hold ''FUNCTION'' and short press ''RESET'' to force boot [[:OOWOW]] service from SPI-flash, and skip other boot sources
+<WRAP important>TF-card slot must be empty.</WRAP>
-Then the boot priority will become:
-  - TF Card
-  - SPI Flash
-  - eMMC

Khadas Docs

User Tools

Site Tools

Differences

Page Tools