Khadas Docs

Amazing Khadas, always amazes you!

User Tools

Site Tools

Home / products / sbc / vim3 / install-os / boot-into-upgrade-mode
products:sbc:vim3:install-os:boot-into-upgrade-mode

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
products:sbc:vim3:install-os:boot-into-upgrade-mode [2022/07/07 23:54]
frank 		products:sbc:vim3:install-os:boot-into-upgrade-mode [2023/03/23 21:33] (current)
nick
Line 1: Line 1:
-====== Boot into Upgrade Mode ======+{{indexmenu_n>30}}
  
-===== Introduction ===== 
  
-===== Into Upgrade Mode =====+====== VIM3/3L Boot into Upgrade Mode ======
  
-<WRAP info > 
 There are 4 ways to boot into upgrade mode: There are 4 ways to boot into upgrade mode:
  
 +  * TST Mode (Recommended)
   * Keys Mode (Side-Buttons)   * Keys Mode (Side-Buttons)
   * Serial Mode   * Serial Mode
-  * TST Mode (Recommended) 
   * MRegister Mode   * MRegister Mode
 +
 +===== TST Mode =====
 +
 +<WRAP tip >
 +TST Mode recommended as preferred upgrade mode
 </WRAP> </WRAP>
  
-<tabbox TST Mode (Recommended)> 
   - Connect VIM3 to PC with a USB-C cable.   - Connect VIM3 to PC with a USB-C cable.
   - Quickly press the ''Function'' key **3 times in 2 seconds**, then release the key. You will see the Power LED (Blue) blink for about 3 seconds.   - Quickly press the ''Function'' key **3 times in 2 seconds**, then release the key. You will see the Power LED (Blue) blink for about 3 seconds.
   - After the Power LED (Red) turns OFF, this indicates that the board is in Upgrade Mode (Maskrom Mode).   - After the Power LED (Red) turns OFF, this indicates that the board is in Upgrade Mode (Maskrom Mode).
-<tabbox Key Mode>+ 
 +===== Key Mode ===== 
  
   - Power on VIM3.   - Power on VIM3.
Line 24: Line 28:
   - Short press the ''Reset'' key and release it.   - Short press the ''Reset'' key and release it.
   - Count for 2 to 3 seconds, then release the ''POWER'' key to enter into Upgrade Mode. You will see the sys-led turn ON when you’ve entered Upgrade Mode.   - Count for 2 to 3 seconds, then release the ''POWER'' key to enter into Upgrade Mode. You will see the sys-led turn ON when you’ve entered Upgrade Mode.
-  -  + 
-<tabbox Serial Mode>+===== Serial Mode ===== 
   - Connect VIM3 to PC with a USB-C cable.   - Connect VIM3 to PC with a USB-C cable.
-  - Refer to [[products:sbc:vim3:development:setup-serial-tool|Setup Serial Too]] to setup your Serial Tool for VIM3.+  - Refer to [[products:sbc:vim3:development:setup-serial-tool|Setup Serial Tool]] to setup your Serial Tool for VIM3.
   - Once again, make sure you’ve done the correct connections and setup.   - Once again, make sure you’ve done the correct connections and setup.
   - Hit ''SPACE'' on your keyboard at the moment of bootup to stop autoboot. This step will let VIM3 boot into U-Boot command line.   - Hit ''SPACE'' on your keyboard at the moment of bootup to stop autoboot. This step will let VIM3 boot into U-Boot command line.
   - Type ''run update'' in the terminal of U-Boot. The Sys LED (White) will turn ON when you’ve entered Upgrade Mode.   - Type ''run update'' in the terminal of U-Boot. The Sys LED (White) will turn ON when you’ve entered Upgrade Mode.
-<tabbox Bootable TF Card>+ 
 +===== MRegister Mode ===== 
 + 
 +  - Power on VIM3. 
 +  - Use a tweezer to short-circuit the two pads of the M register, and without releasing… 
 +  - Short press the Reset key and then release it, to boot into upgroup mode 
 +===== Bootable TF Card ===== 
   - [[products:sbc:vim3:development:create-bootable-tf-card|Create a Bootable TF Card]].   - [[products:sbc:vim3:development:create-bootable-tf-card|Create a Bootable TF Card]].
   - Insert a Bootable TF card into the slot.   - Insert a Bootable TF card into the slot.
Line 38: Line 50:
   - Hit ''SPACE'' key at the moment of bootup to stop autoboot. This step will let VIM3 boot into U-Boot.   - Hit ''SPACE'' key at the moment of bootup to stop autoboot. This step will let VIM3 boot into U-Boot.
   - Type ''run update'' in the U-Boot terminal.   - Type ''run update'' in the U-Boot terminal.
-</tabbox>+
Last modified: 2022/07/07 23:54 by frank

Page Tools

Khadas Site

Khadas Community

Khadas GitHub

Khadas Downloads