This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
products:sbc:vim3:hardware:interfaces [2023/03/21 08:21] hyphop [VIM3/3L Interfaces] |
products:sbc:vim3:hardware:interfaces [2023/03/21 08:59] (current) nick [Table] |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== VIM3/3L Interfaces ====== | ====== VIM3/3L Interfaces ====== | ||
+ | ===== Top Side ===== | ||
- | {{products: | + | {{products: |
- | |||
- | ===== Top Side ===== | ||
| ^ Component | | ^ Component | ||
Line 14: | Line 13: | ||
| 5 | USB-A | USB 2.0 port that supports 500mA output | | 5 | USB-A | USB 2.0 port that supports 500mA output | ||
| 6 | Fan Header | | 6 | Fan Header | ||
- | | 7 | Reset Button | + | | 7 | Reset Button |
- | | 8 | Function Button | + | | 8 | G-Sensor |
- | | 9 | Power Button | + | | 9 | Function Button |
- | | A | M2 Hole | M2 clearance holes for a case, or adding a heatsink | + | | A | Power Button |
- | | B | G-Sensor | + | | B | RTC Header |
- | | C | RTC Header | + | | C | M2 Hole | M2 clearance holes for a case, or adding a heatsink |
| D | 40-Pin GPIO | General input/ | | D | 40-Pin GPIO | General input/ | ||
- | | E | GPIO Expander | + | | E | Infrared Module |
- | | F | MCU | STM8S003 micro-controller with programmable EEPROM | + | | F | LEDs | Indicator LEDs | |
- | | G | WOL Switch | + | | G | GPIO Expander |
- | | H | Infrared Module | + | | H | MCU | STM8S003 micro-controller with programmable EEPROM |
- | | I | LEDs | Indicator LEDs | | + | | I | IPEX Antenna |
- | | J | IPEX Antenna | + | |
- | | K | IPEX Antenna | + | |
===== Back Side ===== | ===== Back Side ===== | ||
- | | ^ Component | + | {{products: |
- | |1|VIN|5-12V power input, supports Power-Over-Ethernet via M2X Extension| | + | |
- | |2|Micro-SD Slot|Molex Slot, spec version 2.x/3.x/4.x (SDSC/ | + | |
- | |3|Current Limit Switch|Prevents damage to VIM3 due to faulty loading conditions| | + | | ^ Component |
- | |4|M.2 Slot|PCIe 2.0 (x1 lane), supports M.2 2280 NVMe SSDs| | + | | 1 | VIN |
- | |5|TP|10-pin 0.5mm pitch FPC connector for touch input| | + | | 2 | Micro-SD Slot |
- | |6|MIPI-DSI|30-pin, | + | | 3 | Current Limit Switch |
- | |7|MIPI-CSI|30-pin, | + | | 4 | M.2 Slot | PCIe 2.0 (x1 lane), supports M.2 2280 NVMe SSDs |
- | |8|SPI | + | | 5 | TP | 10-pin 0.5mm pitch FPC connector for touch input | |
- | |9|XPWR Pads|Connect an external power switch using these pads| | + | | 6 | MIPI-DSI |
- | |A|M-Register|Allows the EMMC to enter MaskROM mode| | + | | 7 | MIPI-CSI |
- | |B|S-Register|Allows | + | | 8 | SPI Flash | Flash memory module that interfaces over SPI | |
+ | | 9 | XPWR Pads | ||
+ | | A | M-Register | ||
+ | | B | S-Register | ||
+ | | C | Current Limit Switch | ||
===== Hardware buttons ===== | ===== Hardware buttons ===== | ||
- | ^ Reset ^ Function | + | {{products: |
- | | x | | | Force Reboot VIM3 | | + | |
- | | | + | |
- | | | + | ^ Reset ^ Function |
- | | x | | x | Enter Upgrade Mode KEYS | | + | | x | | | Force Reboot VIM3 |
+ | | | ||
+ | | | ||
+ | | x | | x | Enter Upgrade Mode (KEY) | | ||