This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
products:sbc:vim3:hardware:interfaces [2022/07/06 10:15] 127.0.0.1 external edit |
products:sbc:vim3:hardware:interfaces [2023/03/21 08:59] (current) nick [Table] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Interfaces ====== | + | ====== |
+ | |||
+ | ===== Top Side ===== | ||
+ | |||
+ | {{products: | ||
+ | |||
+ | |||
+ | | ^ Component | ||
+ | | 1 | USB-A | USB 3.0 port that swaps to 2.0 when PCI-E is active, 900mA output | ||
+ | | 2 | RJ-45 | Gigabit LAN port that supports Wake-On-LAN | ||
+ | | 3 | HDMI | HDMI port supporting CEC | | ||
+ | | 4 | USB-C | USB-C port with USB power delivery (5-20Vinput) and 2.0 speeds, can be used for upgrading the OS | | ||
+ | | 5 | USB-A | USB 2.0 port that supports 500mA output | ||
+ | | 6 | Fan Header | ||
+ | | 7 | Reset Button | ||
+ | | 8 | G-Sensor | ||
+ | | 9 | Function Button | ||
+ | | A | Power Button | ||
+ | | B | RTC Header | ||
+ | | C | M2 Hole | M2 clearance holes for a case, or adding a heatsink | ||
+ | | D | 40-Pin GPIO | General input/ | ||
+ | | E | Infrared Module | ||
+ | | F | LEDs | Indicator LEDs | | ||
+ | | G | GPIO Expander | ||
+ | | H | MCU | STM8S003 micro-controller with programmable EEPROM | ||
+ | | I | IPEX Antenna | ||
+ | |||
+ | ===== Back Side ===== | ||
+ | |||
+ | {{products: | ||
+ | |||
+ | |||
+ | | ^ Component | ||
+ | | 1 | VIN | 5-12V power input, supports Power-Over-Ethernet via M2X Extension | ||
+ | | 2 | Micro-SD Slot | Molex Slot, spec version 2.x/3.x/4.x (SDSC/ | ||
+ | | 3 | Current Limit Switch | ||
+ | | 4 | M.2 Slot | PCIe 2.0 (x1 lane), supports M.2 2280 NVMe SSDs | | ||
+ | | 5 | TP | 10-pin 0.5mm pitch FPC connector for touch input | | ||
+ | | 6 | MIPI-DSI | ||
+ | | 7 | MIPI-CSI | ||
+ | | 8 | SPI Flash | Flash memory module that interfaces over SPI | | ||
+ | | 9 | XPWR Pads | Connect an external power switch using these pads | | ||
+ | | A | M-Register | ||
+ | | B | S-Register | ||
+ | | C | Current Limit Switch | ||
+ | |||
+ | |||
+ | |||
+ | ===== Hardware buttons ===== | ||
+ | |||
+ | {{products: | ||
+ | |||
+ | |||
+ | ^ Reset ^ Function | ||
+ | | x | | | Force Reboot VIM3 | | ||
+ | | | ||
+ | | | ||
+ | | x | | x | Enter Upgrade Mode (KEY) | | ||
+ | |||
+ | |||
+ | ===== GPIO header pinout ===== | ||
+ | |||
+ | ^ SIGNAL | ||
+ | | 5V | 1 | 21 | **GND** | ||
+ | | 5V | 2 | 22 | I2C_M3_SCL | ||
+ | | USB_DM | ||
+ | | USB_DP | ||
+ | | **GND** | ||
+ | | VCC_MCU | ||
+ | | MCU_NRST | ||
+ | | MCU_SWIM | ||
+ | | **GND** | ||
+ | | ADC_CH0 | ||
+ | | 1.8V | 11 | 31 | I2SB_SDO | ||
+ | | ADC_CH3 | ||
+ | | SPDIF_OUT | ||
+ | | **GND** | ||
+ | | UARTC_RX | ||
+ | | UARTC_TX | ||
+ | | **GND** | ||
+ | | Linux_RX | ||
+ | | Linux_TX | ||
+ | | 3.3V | 20 | 40 | **GND** | ||