This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
products:sbc:vim1s:hardware:interfaces [2022/07/17 21:31] 127.0.0.1 external edit |
products:sbc:vim1s:hardware:interfaces [2022/10/20 02:22] (current) hyphop [GPIO Pinout] |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== | + | ====== |
- | {{: | + | ===== Top side ===== |
- | {{:products: | + | {{products: |
- | <tabbox Front(Blue)> | + | | ^ Component |
+ | | 1 | USB-A | USB 2.0 speed, 500mA max output | ||
+ | | 2 | RJ-45 | 10/100 Mbps Ethernet | ||
+ | | 3 | HDMI | HDMI 2.1b with 3D, HDR, CEC and HDCP 2.2 | | ||
+ | | 4 | USB-C | USB 2.0 OTG and 5V power input, can be used for upgrading the OS | | ||
+ | | 5 | USB-A | USB 2.0 speed, 750mA max output | ||
+ | | 6 | Fan header | ||
+ | | 7 | Reset button | ||
+ | | 8 | Function button | ||
+ | | 9 | Power button | ||
+ | | A | RTC battery header | ||
+ | | B | SPI-Flash | ||
+ | | C | 40-Pin GPIO | [[products/ | ||
+ | | D | Infrared module | ||
+ | | E | LEDs | Status indicator LEDs | | ||
+ | | F | MCU | Advanced device hardware control | ||
+ | | G | MHF2 Wi-Fi/BT connector | ||
- | | ^ Component | + | ===== Back side ===== |
- | | 1 | USB-A | USB 3.0 port that supports 1500mA output | + | |
- | | 2 | RJ-45 | Gigabit LAN port that supports Wake-On-LAN | | + | {{products: |
- | | 3 | HDMI Output | + | |
- | | 4 | USB-C | USB-C port with USB power delivery (9-20V input) and 2.0 speeds, can be used for upgrading the OS | | + | |
- | | 5 | USB-A | USB 2.0 port that supports 1300mA output | + | |
- | | 6 | Fan Header | + | |
- | | 7 | Reset Button | + | |
- | | 8 | Function Button | + | |
- | | 9 | Power Button | + | |
- | | A | RTC Header | + | |
- | | B | M2 Hole | M2 clearance holes for a case, or adding a heatsink | + | |
- | | C | 40-Pin GPIO | General input/ | + | |
- | | D | DMIC | Digital Microphone | + | |
- | | E | HDMI Input | Type-D HDMI input | | + | |
- | | F | LEDs | Indicator LEDs | | + | |
- | | G | MCU | STM32G0 micro-controller | + | |
- | | H | MHF4 Antenna | + | |
- | | I | MHF4 Antenna | + | |
- | | J | Current Limit Switch | + | |
- | <tabbox Back(Red)> | + | | ^ Component |
+ | |1|VIN|5V additional power input| | ||
+ | |2|Micro-SD card slot|SD-card storage, or boot device from SD card | | ||
+ | |3|IO|Extension FPC IO connector| | ||
+ | |4|XPWR Pads|Connect an external power switch using these pads| | ||
- | ^ ^ Component | ||
- | | 1 | VIN | 9-20V power input | | ||
- | | 2 | Micro-SD Slot | Molex Slot, spec version 2.x/3.x/4.x (SDSC/ | ||
- | | 3 | M.2 Slot | PCIe 2.0 (x1 lane), supports M.2 2280 NVMe SSDs | | ||
- | | 4 | MIPI-CSI | ||
- | | 5 | MIPI-CSI | ||
- | | 6 | MIPI-DSI& | ||
- | | 7 | V-by-One | ||
- | | 8 | XPWR Pads | Connect an external power switch using these pads | | ||
- | | 9 | SPI Flash | Flash memory module that interfaces over SPI | | ||
- | | A | Current Limit Switch | ||
- | | B | G-Sensor | ||
- | <tabbox Buttons> | + | ===== Hardware buttons ===== |
- | ^ Reset ^ Function | + | {{: |
- | | x | + | |
- | | | x | | Enter Upgrade Mode (TST) | | + | |
- | | | | + | |
- | | | | + | |
- | <tabbox Indicator LEDs> | + | ^ |
- | ^ Colour | + | | |
- | | Red | OFF | + | | |
- | | | + | | | | x | Power-On / Wake-Up device |
- | | White | OFF | + | | |
- | | | + | |
- | <WRAP important > | + | ==== Special button shortcuts ==== |
- | The above behaviours are default out-of-the-box, | + | |
- | </ | + | |
- | <tabbox GPIO Pinout> | + | * Press '' |
+ | * Boot [[OOWOW:]] - hold '' | ||
+ | * Other [[software/ | ||
- | {{: | + | ===== GPIO Header pin-out ===== |
- | </ | + | {{: |
+ | [[../ | ||
+ | |||
+ | /* | ||
+ | ===== VIM1S interfaces gallery ===== | ||
+ | |||
+ | {{gallery> | ||
+ | |||
+ | */ |