This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
products:sbc:vim1s:hardware:interfaces [2022/09/22 23:14] hyphop |
products:sbc:vim1s:hardware:interfaces [2022/09/23 22:17] nick [Table] |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== VIM1S Interfaces ====== | ====== VIM1S Interfaces ====== | ||
- | {{gallery> | + | ===== Top side ===== |
- | /* | + | {{products: |
- | {{gallery>.?lightbox& | + | |
- | {{../ | + | | ^ Component |
- | {{../ | + | | 1 | USB-A | USB 2.0 speed, 500mA max output |
- | {{../vim1s-interfaces-03.webp? | + | | 2 | RJ-45 | 10/100 Mbps Ethernet |
- | {{../vim1s-interfaces-04.webp?400}} | + | | 3 | HDMI | HDMI 2.1b with 3D, HDR, CEC and HDCP 2.2 | |
- | */ | + | | 4 | USB-C | USB 2.0 OTG and 5V power input, can be used for upgrading the OS | |
+ | | 5 | USB-A | USB 2.0 speed, 750mA max output | ||
+ | | 6 | Fan header | ||
+ | | 7 | Reset button | ||
+ | | 8 | Function button | ||
+ | | 9 | Power button | ||
+ | | A | RTC battery header | ||
+ | | B | SPI-Flash | ||
+ | | C | 40-Pin GPIO | [[products/ | ||
+ | | D | Infrared module | ||
+ | | E | LEDs | Status indicator LEDs | | ||
+ | | F | MCU | Advanced device hardware control | ||
+ | | G | MHF2 Wi-Fi/BT connector | ||
- | /* | + | ===== Back side ===== |
- | {{:products: | + | |
+ | {{products: | ||
- | {{: | ||
- | */ | ||
- | <tabbox Front(Blue)> | ||
| ^ Component | | ^ Component | ||
- | |1|USB-A|USB 2.0 speed, 500mA max output| | + | |1|VIN|5V additional |
- | |2|RJ-45|10/ | + | |2|Micro-SD card slot|SD-card storage, or boot device from SD card | |
- | |3|HDMI|HDMI 2.1b with 3D, HDR, CEC and HDCP 2.2| | + | |3|IO|Extension FPC IO connector| |
- | |4|USB-C|USB 2.0 OTG and 5V power input, can be used for upgrading the OS| | + | |4|XPWR Pads|Connect an external power switch using these pads| |
- | |5|USB-A|USB | + | |
- | |6|Fan Header|4-wire fan header utilising pulse width modulation| | + | |
- | |7|Reset Button|Force reboot your VIM1S in the event of a system freeze| | + | |
- | |8|Function Button|Press this 3 times in 2 seconds to enter MaskROM mode| | + | |
- | |9|Power Button|This button turns on your VIM1S| | + | |
- | |A|RTC Battery Header|Header for attaching a battery for the real time clock| | + | |
- | |B|SPI Flash|Flash memory module that interfaces over SPI| | + | |
- | |C|40-Pin GPIO|Learn how to access the GPIO from here, or use it to add a Toneboard| | + | |
- | |D|Infrared Module|Dual channel infrared receiver for use with Khadas IR remote| | + | |
- | |E|LEDs|Status indicator LEDs| | + | |
- | |F|MHF2 Wi-Fi / Bluetooth Connector|Wi-Fi / BT Antenna connector| | + | |
- | <tabbox Back(Red)> | ||
+ | ===== Hardware buttons ===== | ||
- | | ^ Component | + | {{: |
- | |1|VIN|5V power input| | + | |
- | |2|Micro-SD Card Slot|Boot alternative OSes via a Micro-SD card, and for extra storage| | + | |
- | |3|IO|FPC IO connector| | + | |
- | |4|XPWR Pads|Connect an external power switch using these pads| | + | |
+ | ^ Reset ^ Function | ||
+ | | x | | | Hardware device reset | | ||
+ | | | ||
+ | | | ||
+ | | x | | x | Enter upgrade mode (KEYS) | ||
- | <tabbox Buttons> | + | ==== Special button shortcuts ==== |
- | ^ Reset ^ Function | + | * Press '' |
- | |x| | |Force Reboot VIM1S| | + | * Boot [[oowow:]] - hold '' |
- | | |x| |Enter Upgrade Mode (TST)| | + | ===== GPIO Pinout ===== |
- | | | |x|Power On/Wake Up VIM1S| | + | |
- | |x| |x|Enter Upgrade Mode (KEYS)| | + | |
- | |x|x|x|Erase EMMC| | + | |
+ | WIP: | ||
+ | /* | ||
+ | ===== VIM1S interfaces gallery ===== | ||
- | <tabbox GPIO Pinout> | + | {{gallery>../? |
- | + | */ | |
- | </tabbox> | + |