Differences

This shows you the differences between two versions of the page.

--- products:sbc:edge2:install-os:boot-into-upgrade-mode [2022/07/15 23:37]
127.0.0.1 external edit
+++ products:sbc:edge2:install-os:boot-into-upgrade-mode [2022/09/27 23:55] (current)
nick
@@ Line 1: / Line 1: @@
-====== Edge1 Boot into Upgrade Mode ======
+{{indexmenu_n>40}}
+====== Edge2 Boot into Upgrade Mode ======
 ===== Introduction =====
@@ Line 5: / Line 8: @@
 <WRAP info >
-There are 4 ways to boot into upgrade mode:
+There are 3 ways to boot into upgrade mode:
-  * Keys Mode (Side-Buttons)
-  * Serial Mode
   * TST Mode (Recommended)
-  * MRegister Mode
+  * Serial Mode
+  * Linux/Android Command Line
 </WRAP>
 <tabbox TST Mode (Recommended)>
-  - Connect Edge1 to PC with a USB-C cable.
+  - Connect Edge2 to PC with a USB-C cable.
-  - Quickly press the ''Function'' key **3 times in 2 seconds**, then release the key. You will see the Power LED (Blue) blink for about 3 seconds.
+  - Quickly press the ''Function'' key **3 times in 2 seconds**, then release the key. You will see the Power LED (Red) blink for about 3 seconds.
-  - After the Power LED (Red) turns OFF, this indicates that the board is in Upgrade Mode (Maskrom Mode).
+  - After the ''Power LED'' (Red) turns OFF, this indicates that the board is in Upgrade Mode (Maskrom Mode).
-<tabbox Key Mode>
-  - Power on Edge1.
-  - Long press the ''POWER'' key without releasing it.
-  - Short press the ''Reset'' key and release it.
-  - Count for 2 to 3 seconds, then release the ''POWER'' key to enter into Upgrade Mode. You will see the sys-led turn ON when you’ve entered Upgrade Mode.
 <tabbox Serial Mode>
-  - Connect Edge1 to PC with a USB-C cable.
+  - Connect Edge2 to PC with a USB-C cable.
-  - Refer to [[products:sbc:edge1:development:setup-serial-tool|Setup Serial Tool]] to setup your Serial Tool for Edge1.
+  - Refer to [[products:sbc:edge2:development:setup-serial-tool|Setup Serial Tool]] to setup your Serial Tool for Edge2.
   - Once again, make sure you’ve done the correct connections and setup.
-  - Hit ''SPACE'' on your keyboard at the moment of bootup to stop autoboot. This step will let Edge1 boot into U-Boot command line.
+  - Hit ''SPACE'' on your keyboard at the moment of bootup to stop autoboot. This step will let Edge2 boot into U-Boot command line.
-  - Type ''run update'' in the terminal of U-Boot. The Sys LED (White) will turn ON when you’ve entered Upgrade Mode.
+  - Type ''run update'' in the terminal of U-Boot. The ''Red LED'' will turn ON when you’ve entered Upgrade Mode.
-<tabbox Bootable TF Card>
-  - [[products:sbc:edge1:development:create-bootable-tf-card|Create a Bootable TF Card]].
+<tabbox Linux Command Line>
-  - Insert a Bootable TF card into the slot.
+  - Refer to this [[/products/sbc/edge2/development/setup-serial-tool|guide]] to setup your serial tool for Edge2.
-  - Refer to this guide to setup your serial tool for Edge1.
+  - Once again, make sure you’ve done the correct connections and setup.
-  - Connect Edge1 to PC with a USB-C cable.
+  - Boot into Android or Linux command line.
-  - Hit ''SPACE'' key at the moment of bootup to stop autoboot. This step will let Edge1 boot into U-Boot.
+  - For Linux, execute ''sudo reboot loader''. For Android, execute ''su'' and ''reboot loader''. The system will reboot and enter Upgrade Mode. You will see the ''Red LED'' turn ON when you’ve entered Upgrade Mode (Loader Mode).
-  - Type ''run update'' in the U-Boot terminal.
 </tabbox>

Khadas Docs

User Tools

Site Tools

Differences

Page Tools