Khadas Docs

Amazing Khadas, always amazes you!

User Tools

Site Tools

Home / products / sbc / edge1 / install-os / boot-into-upgrade-mode
products:sbc:edge1:install-os:boot-into-upgrade-mode

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision 		Previous revision
products:sbc:edge1:install-os:boot-into-upgrade-mode [2022/07/10 22:43]
frank created 		products:sbc:edge1:install-os:boot-into-upgrade-mode [2022/11/22 21:27] (current)
nick
Line 1: Line 1:
-====== Boot into Upgrade Mode ======+{{indexmenu_n>30}} 
 + 
 + 
 +====== Edge1 Boot into Upgrade Mode ======
  
 ===== Introduction ===== ===== Introduction =====
  
-===== Into Upgrade Mode ===== 
  
 <WRAP info > <WRAP info >
-There are 4 ways to boot into upgrade mode:+There are 5 ways to boot into upgrade mode:
  
-  * Keys Mode (Side-Buttons) 
-  * Serial Mode 
   * TST Mode (Recommended)   * TST Mode (Recommended)
-  * MRegister Mode+  * Keys Mode 
 +  * Serial Mode 
 +  * Linux/Android Command Line 
 +  * MRegister Mode (Maskrom Mode)
 </WRAP> </WRAP>
  
Line 18: Line 21:
   - Quickly press the ''Function'' key **3 times in 2 seconds**, then release the key. You will see the Power LED (Blue) blink for about 3 seconds.   - Quickly press the ''Function'' key **3 times in 2 seconds**, then release the key. You will see the Power LED (Blue) blink for about 3 seconds.
   - After the Power LED (Red) turns OFF, this indicates that the board is in Upgrade Mode (Maskrom Mode).   - After the Power LED (Red) turns OFF, this indicates that the board is in Upgrade Mode (Maskrom Mode).
 +
 <tabbox Key Mode> <tabbox Key Mode>
  
Line 31: Line 35:
   - Hit ''SPACE'' on your keyboard at the moment of bootup to stop autoboot. This step will let Edge1 boot into U-Boot command line.   - Hit ''SPACE'' on your keyboard at the moment of bootup to stop autoboot. This step will let Edge1 boot into U-Boot command line.
   - Type ''run update'' in the terminal of U-Boot. The Sys LED (White) will turn ON when you’ve entered Upgrade Mode.   - Type ''run update'' in the terminal of U-Boot. The Sys LED (White) will turn ON when you’ve entered Upgrade Mode.
-<tabbox Bootable TF Card> +  - Type ''run maskrom'' on the terminal of U-Boot as below, and you will enter Maskrom Mode. 
-  - [[products:sbc:edge1:development:create-bootable-tf-card|Create a Bootable TF Card]]. + 
-  - Insert a Bootable TF card into the slot. +<tabbox Linux Command Line> 
-  - Refer to this guide to setup your serial tool for Edge1. +  - Refer to this [[/products/sbc/edge1/development/setup-serial-tool|guide]] to setup your serial tool for Edge. 
-  - Connect Edge1 to PC with a USB-C cable. +  - Once again, make sure you’ve done the correct connections and setup. 
-  - Hit ''SPACE'' key at the moment of bootup to stop autoboot. This step will let Edge1 boot into U-Boot. +  - Boot into Android or Linux command line. 
-  - Type ''run update'' in the U-Boot terminal.+  - For Linux, execute sudo reboot loader. For Android, execute su and reboot loader. The system will reboot and enter Upgrade Mode. You will see the sys-led turn ON when you’ve entered Upgrade Mode (Loader Mode). 
 + 
 +<tabbox MRegister Mode(Maskrom Mode)> 
 + 
 +  - Power-on Edge. 
 +  - Use a tweezer to short-circuit the two pads of ''M'' register, then without releasing. 
 +  - Short press the ''Reset'' key and release it to boot into Upgrade Mode (Maskrom Mode). 
 + 
 +{{products:sbc:edge1:install-os:edge1-mregister-short-circuit.webp}} 
 </tabbox> </tabbox>
Last modified: 2022/07/10 22:43 by frank

Page Tools

Khadas Site

Khadas Community

Khadas GitHub

Khadas Downloads