Khadas Docs

Amazing Khadas, always amazes you!

User Tools

Site Tools

Home / products / sbc / common / development / setup-serial-tool
products:sbc:common:development:setup-serial-tool

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision 		Previous revision
products:sbc:common:development:setup-serial-tool [2022/06/29 21:51]
127.0.0.1 external edit 		products:sbc:common:development:setup-serial-tool [2022/10/16 02:20] (current)
hyphop [Hardware Connection]
Line 1: Line 1:
 ====== Setup Serial Tool ====== ====== Setup Serial Tool ======
 +
 +===== Introduction =====
 +
 +This page will introduce the serial tool. You will learn how to connect Khadas SBC to PC and install debugging software on different PCs.
 +
 +===== Preparation =====
 +
 +Take a serial tool, which is also known as an USB to TTL Converter like [[https://www.amazon.com/Adaptor-Download-Adapter-Converter-LinkMore/dp/B08VGRRJ67/ref=sr_1_4?dchild=1&keywords=USB+to+TTL+ch340&qid=1629184609&sr=8-4|CH340 USB to TTL Converter]].
 +
 +===== Hardware Connection =====
 +
 +{{ /products/sbc/common/development/serial_connections_3pin.png?500|serial_connections}}
 +
 +You can connect your serial tool to the board GPIO pins, referring to the following diagram，
 +
 +^ Serial tools pin ^ GPIO board header pin ^ Name ^
 +| ''GND'' |  ''17''  | |
 +| ''TXD'' |  ''18''  | ''Linux_Rx'' | 
 +| ''RXD'' |  ''19''  | ''Linux_Tx'' |
 +| ''VCC'' |  ''20''  | |
 +
 +/*
 +  * Tool Pin ''GND'' <-> ''Pin17'' of VIM’s GPIO
 +  * Tool Pin ''TXD'' <-> ''Pin18'' of VIM’s GPIO ''Linux_Rx''
 +  * Tool Pin ''RXD'' <-> ''Pin19'' of VIM’s GPIO ''Linux_Tx''
 +  * Tool Pin ''VCC'' <-> ''Pin20'' of VIM’s GPIO
 +*/
 +Insert the USB port into your computer.
 +
 +  * Blue line: ''TXD''
 +  * Orange line: ''RXD''
 +  * Black line: ''GND''
 +
 +===== Setup Serial Communication Program =====
 +
 +<WRAP important >
 +  * VIM1/VIM2/VIM3/VIM3L Baudrate: **115200**
 +  * VIM4/VIM1S Baudrate: **921600**
 +  * Edge1/Edge2 Baudrate: **1500000**
 +</WRAP>
 +
 +<tabbox Ubuntu> 
 +
 +Use the ''minicom'' serial communication program.
 +
 +1. **Install**
 +
 +```shell
 +$ sudo apt update
 +$ sudo apt install minicom
 +```
 +Add permissions to access
 +```shell
 +$ sudo usermod -a -G dialout $(whoami)
 +```
 +<WRAP info >
 +You may need to logout or reboot your system to take effect.
 +</WRAP>
 +
 +2. **Setup**
 +
 +Connect your SBC to the computer via the USB to TTL Converter tool before setting up ''minicom''.
 +
 +```shell
 +$ sudo minicom -s
 +```
 +
 +Enter the ''minicom'' setup mode:
 +```
 ++-----[configuration]------+
 +| Filenames and paths      |
 +| File transfer protocols  |
 +| Serial port setup        |
 +| Modem and dialing        |
 +| Screen and keyboard      |
 +| Save setup as dfl        |
 +| Save setup as..          |
 +| Exit                     |
 +| Exit from Minicom        |
 ++--------------------------+
 +```
 +Use the up/down arrow keys to shift to ''Serial port setup'', and hit Enter to enter the ''Serial port setup menu''.
 +
 +  * You can use ''Shift'' + ''A'' to setup the serial device, hit Enter to confirm.
 +  * You can use ''Shift'' + ''E'' to setup the baudrate, choose ''115200'' and hit Enter to confirm.
 +  * You can use ''Shift'' + ''F'' to disable the hardware flow control, set to ''NO''.
 +
 +After completing the setup, hit Enter to exit, then choose Save setup as dfl, then Exit from Minicom.
 +<WRAP info >
 +The serial device node must correspond to Ubuntu’s serial device node.
 +</WRAP>
 +
 +3. **Launch**
 +
 +Type ''minicom'' into the Ubuntu Terminal:
 +
 +```
 +$ minicom
 +elcome to minicom 2.7.1
 +
 +OPTIONS: I18n 
 +Compiled on Dec 23 2019, 02:06:26.
 +Port /dev/ttyUSB0, 15:24:13
 +
 +Press CTRL-A Z for help on special keys
 +
 +Ubuntu 20.04.2 LTS Khadas ttyS0
 +
 +Khadas login: 
 +```
 +
 +4. **Exit**
 +
 +You can use ''Ctrl''+''A''+''Z'' to open the menu:
 +```
 ++-------------------------------------------------------------------+
 +|                      Minicom Command Summary                      |
 +|                                                                   |
 +|              Commands can be called by CTRL-A <key>               |
 +|                                                                   |
 +|               Main Functions                  Other Functions     |
 +|                                                                   |
 +| Dialing directory..D  run script (Go)....G | Clear Screen.......C |
 +| Send files.........S  Receive files......R | cOnfigure Minicom..O |
 +| comm Parameters....P  Add linefeed.......A | Suspend minicom....J |
 +| Capture on/off.....L  Hangup.............H | eXit and reset.....X |
 +| send break.........F  initialize Modem...M | Quit with no reset.Q |
 +| Terminal settings..T  run Kermit.........K | Cursor key mode....I |
 +| lineWrap on/off....W  local Echo on/off..E | Help screen........Z |
 +| Paste file.........Y  Timestamp toggle...N | scroll Back........B |
 +| Add Carriage Ret...U                                              |
 +|                                                                   |
 +|             Select function or press Enter for none.              |
 ++-------------------------------------------------------------------+
 +```
 +Use ''Shift''+''Q'' to exit ''minicom''.
 +
 +```
 ++----------------------+
 +| Leave without reset? |
 +|     Yes       No     |
 ++----------------------+
 +```
 +Choose ''Yes'' and hit Enter to exit ''minicom''.
 +
 +
 +<WRAP info >
 +  * If the Terminal output contains this line, you need to use ''sudo minicom''.\\ ```sh
 +/dev/ttyUSB0: Permission denied
 +```
 +  * To access U-Boot, leave your USB-Serial-Debug tool connected, then press the reset button on your device once. You should see some print-out on your Terminal, then quickly press the ''space'' or ''control-c'' to stop auto-boot. You will see the prompt ''kvim#'' when you've entered U-boot.
 +  * Standard “help” commands are listed in U-Boot Usage Guide, you’ll need to first have a version of Android or Ubuntu installed in your VIM device, from our [[https://dl.khadas.com/Firmware/Krescue/images|official OOWOW]] images.
 +</WRAP>
 +
 +<tabbox Windows> 
 +
 +1. Install Driver
 +
 +Install the CH340 driver.
 +
 +  - Download the [[https://dl.khadas.com/Tools/CH34x_Install_Windows_v3_4.zip|driver]].
 +  - Unzip the compressed file.
 +  - Run the installer.
 +
 +2. Install SecureCRT
 +
 +Download the program from the [[https://www.vandyke.com/products/securecrt|SecureCRT]] website.
 +
 +3. Setup SecureCRT
 +
 +Before starting SecureCRT, you’ll need to connect the USB to TTL Converter tool to your SBC and computer.
 +
 +Launch SecureCRT and navigate to ''File''->''Quick Connect'':
 +
 +{{/products/sbc/common/development/securecrt1.png|securecrt1}}
 +
 +Select the ''Serial'' protocol, select the correct device node, set the baudrate to ''115200'', unselect ''XON/XOFF''.
 +
 +{{/products/sbc/common/development/securecrt2.png|securecrt2}}
 +
 +Click ''Connect''.
 +
 +{{/products/sbc/common/development/securecrt3.png|securecrt3}}
 +
 +<tabbox Mac OS> 
 +
 +1. Setup Meta key
 +
 +minicom needs a Meta key. Use Terminal to create a Meta key.
 +Go to ''Terminal''->''Preferences''->''Keyboard'', select Use Option as Meta key.
 +
 +{{/products/sbc/common/development/minicom1_en.png|minicom1_en}} \\
 +{{/products/sbc/common/development/minicom2_en.png|minicom2_en}} \\
 +{{/products/sbc/common/development/minicom3_en.png|minicom3_en}}
 +
 +2. Install
 +
 +```shell
 +$ sudo apt update
 +$ sudo apt install minicom
 +```
 +Add access permissions
 +```shell
 +$ sudo usermod -a -G dialout $(whoami)
 +```
 +<WRAP info >
 +You may need to logout or reboot your system for changes to take effect.
 +</WRAP>
 +
 +3. Setup
 +
 +Connect the USB to TTL Converter tool to your SBC and computer before setting up ''minicom''.
 +```shell
 +$ sudo minicom -s
 +```
 +Enter the minicom setup mode:
 +```
 ++-----[configuration]------+
 +| Filenames and paths      |
 +| File transfer protocols  |
 +| Serial port setup        |
 +| Modem and dialing        |
 +| Screen and keyboard      |
 +| Save setup as dfl        |
 +| Save setup as..          |
 +| Exit                     |
 +| Exit from Minicom        |
 ++--------------------------+
 +```
 +Use the up/down arrows to shift to ''Serial port setup'', and hit Enter to enter the ''Serial port setup menu''.
 +
 +  * You can use ''Shift'' + ''A'' to setup the serial device, hit Enter to confirm.
 +  * You can use ''Shift'' + ''E'' to setup the baudrate, choose ''115200'' and hit Enter to confirm.
 +  * You can use ''Shift'' + ''F'' to disable the hardware flow control, set to ''NO''.
 +
 +After completing the setup, hit Enter to exit, then choose Save setup as dfl, then Exit from Minicom.
 +
 +<WRAP info >
 +The serial device node must correspond to the Mac OS’ serial device node.
 +</WRAP>
 +
 +4. Launch
 +
 +Type ''minicom'' into the Ubuntu Terminal:
 +
 +```
 +$ minicom
 +elcome to minicom 2.7.1
 +
 +OPTIONS: I18n 
 +Compiled on Dec 23 2019, 02:06:26.
 +Port /dev/ttyUSB0, 15:24:13
 +
 +Press CTRL-A Z for help on special keys
 +
 +Ubuntu 20.04.2 LTS Khadas ttyS0
 +
 +Khadas login: 
 +```
 +
 +5. Exit
 +
 +You can use ''Ctrl''+''A''+''Z'' to open the menu:
 +```
 ++-------------------------------------------------------------------+
 +|                      Minicom Command Summary                      |
 +|                                                                   |
 +|              Commands can be called by CTRL-A <key>               |
 +|                                                                   |
 +|               Main Functions                  Other Functions     |
 +|                                                                   |
 +| Dialing directory..D  run script (Go)....G | Clear Screen.......C |
 +| Send files.........S  Receive files......R | cOnfigure Minicom..O |
 +| comm Parameters....P  Add linefeed.......A | Suspend minicom....J |
 +| Capture on/off.....L  Hangup.............H | eXit and reset.....X |
 +| send break.........F  initialize Modem...M | Quit with no reset.Q |
 +| Terminal settings..T  run Kermit.........K | Cursor key mode....I |
 +| lineWrap on/off....W  local Echo on/off..E | Help screen........Z |
 +| Paste file.........Y  Timestamp toggle...N | scroll Back........B |
 +| Add Carriage Ret...U                                              |
 +|                                                                   |
 +|             Select function or press Enter for none.              |
 ++-------------------------------------------------------------------+
 +```
 +Use ''Shift''+''Q'' to exit ''minicom''.
 +
 +```
 ++----------------------+
 +| Leave without reset? |
 +|     Yes       No     |
 ++----------------------+
 +```
 +Choose ''Yes'' and hit Enter to exit ''minicom''.
 +</tabbox>
 +
  
Last modified: 2022/06/29 21:51 by 127.0.0.1

Page Tools

Khadas Site

Khadas Community

Khadas GitHub

Khadas Downloads