User Tools
products:sbc:common:add-ons:m2xeth
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Last revision Both sides next revision | ||
|
products:sbc:common:add-ons:m2xeth [2023/03/23 05:40] xiong |
products:sbc:common:add-ons:m2xeth [2023/03/23 21:22] nick |
||
|---|---|---|---|
| Line 51: | Line 51: | ||
| ``` | ``` | ||
| - | ===== Android ===== | ||
| - | |||
| - | *before you use the M2x ethernet ,you should enable m2x ethernet by two method | ||
| - | |||
| - | ===== Enable m2x ethernet on tv setting ===== | ||
| - | |||
| - | *Enter Droid Settings-> | ||
| - | |||
| - | {{/ | ||
| - | |||
| - | ===== Enable m2x ethernet by kbi command ===== | ||
| - | |||
| - | *About kbi usage ,you can refer kbi guide,set command as followimg | ||
| - | |||
| - | ```shell | ||
| - | kvim3#kbi | ||
| - | kbi - Khadas Bootloader Instructions sub-system | ||
| - | |||
| - | Usage: | ||
| - | kbi [function] [mode] [write|read] < | ||
| - | |||
| - | kbi version - read version information | ||
| - | kbi usid - read usid information | ||
| - | kbi powerstate - read power on state | ||
| - | kbi poweroff - power off device | ||
| - | kbi ethmac - read ethernet mac address | ||
| - | kbi hwver - read board hardware version | ||
| - | |||
| - | kbi led [systemoff|systemon] w < | ||
| - | kbi led [systemoff|systemon] r - read blue led mode | ||
| - | |||
| - | kbi forcereset [wol|gpio] w <0|1> - disable/ | ||
| - | kbi forcereset [wol|gpio] r - read state of force-reset | ||
| - | [notice: the wol|gpio boot trigger must be enabled if you want to enable force-reset] | ||
| - | |||
| - | kbi bootmode w < | ||
| - | kbi bootmode r - read current bootmode | ||
| - | |||
| - | kbi portmode w <0|1> - set port as usb3.0 or pcie | ||
| - | kbi portmode r - read current port mode | ||
| - | kbi ext_ethernet w <0|1> - set ethernet from internal or m2x | ||
| - | kbi ext_ethernet r - read current ethernet mode | ||
| - | kbi tststatus r - read TST status | ||
| - | kbi tststatus clear - clear TST status | ||
| - | |||
| - | kbi forcebootsd | ||
| - | kbi wolreset | ||
| - | |||
| - | kbi ircode [customer1|customer2] w < | ||
| - | kbi ircode [customer1|customer2] r | ||
| - | kbi trigger [wol|rtc|ir|dcin|key|gpio] w <0|1> - disable/ | ||
| - | kbi trigger [wol|rtc|ir|dcin|key|gpio] r - read mode of a boot trigger | ||
| - | kvim3#kbi ext_ethernet w 1 | ||
| - | [reg_31] 0x1d9a | ||
| - | [reg_16] 0x40 | ||
| - | [reg_17] 0x7fbf | ||
| - | [reg_19] 0x0 | ||
| - | [reg_31] 0x0 | ||
| - | [reg_31] 0xd40 | ||
| - | [reg_22] 0x0 | ||
| - | [reg_31] 0x0 | ||
| - | set m2x ethernet | ||
| - | kvim3#kbi ext_ethernet r | ||
| - | use m2x ethernet | ||
| - | kvim3# | ||
| - | ``` | ||
| - | |||
| - | *kbi ext_ethernet w 1 is to use m2x ethernet, | ||
Last modified: 2024/03/19 03:46 by ivan