====== Edge1 Interfaces ====== ===== Top Side ===== {{products:sbc:edge1:hardware:edge1-interfaces-top-side.webp?600}} | ^ Component ^ Purpose ^ | 1 | USB-A | USB 3.0, blue colour | | 2 | RJ-45 | Gigabit Ethernet with Wake-On-LAN (WOL) | | 3 | HDMI | Type-A Female, up to 4K@60Hz, HDCP 2.2 | | 4 | USB-C | USB 3.0, Display Port v1.2, can be used for upgrading the OS | | 5 | USB-A | USB 2.0, black colour | | 6 | Fan Header | 4-wire fan header utilising pulse width modulation | | 7 | Reset Button | Force reboot your Edge-V | | 8 | Function Button | Press this 3 times in 2 seconds to enter MaskROM mode | | 9 | Power Button | This button turns on your Edge-V | | A | RTC Battery Header | Header for attaching a battery for the real time clock | | B | M2 Hole | M2 clearance holes for a case, or adding a heatsink | | C | 40-Pin GPIO | access GPIO, or use it to add a Toneboard | | D | Gesture Sensor | Control your Edge-V with a hand-wave | | E | Infrared Module | 2-channel infrared receiver for use with Khadas IR remote | | F | LEDs | Status indicator LEDs | | G | I-Pex Wi-Fi / Bluetooth Connector | Wi-Fi / BT Antenna connector | ===== Back Side ===== {{products:sbc:edge1:hardware:edge1-interfaces-back-side.webp?600}} | ^ Component ^ Purpose ^ | 1 | USB-C | USB-C port that accepts 5-20V power input (PD only) | | 2 | Micro-SD Card Slot | Boot alternative OSes via a Micro-SD card, or just for extra storage | | 3 | M.2 Socket (PCI-E 2.1) | Connect 2280 NVMe SSDS at 4-lane speed with M2X Extension | | 4 | E-DP Display | For connecting to external displays via E-DP | | 5 | Touch Panel | For accepting touch-input | | 6 | MIPI-DSI | MIPI-DSI header for connecting LCD screens | | 7 | MIPI-CSI | For connecting to MIPI-CSI cameras | | 8 | MIPI-CSI | For connecting to MIPI-CSI cameras | | 9 | M-Register | Another way for entering upgrade mode | | A | Li-Po Battery Connector | Connect a Lithium Polymer battery with the [[https://www.khadas.com/product-page/juice-board |Juice Board]]| ===== Hardware buttons ===== {{products:sbc:edge1:hardware:edge1-buttons.webp?400}} ^ Reset ^ Function ^ Power ^ Purpose ^ | x | | | Force Reboot Edge-V | | | x | | Enter Upgrade Mode (TST) | | | | x | Power On/Wake Up Edge-V | | x | | x | Enter Upgrade Mode (KEY) | ===== GPIO header pinout ===== ^SIGNAL ^PIN ^PIN ^SIGNAL ^ |5V|1|21|GND| |5V|2|22|SPI3_RXD/I2C0_SCK/GPIO1_C0| |HOST1_DM|3|23|SPI3_TXD/I2C0_SDA/GPIO1_B7| |HOST1_DP|4|24|GND| |GND|5|25|I2C2_SCL/GPIO2_A1| |MCU_TX|6|26|I2C2_SDA/GPIO2_A0| |MCU_NRST|7|27|3.3V| |MCU_SWIM|8|28|GND| |GND|9|29|I2S0_SCLK/GPIO3_D0| |ADC_IN2|10|30|I2S_CLK/GPIO4_A0| |1.8V|11|31|I2S0_SDO0/GPIO3_D7| |ADC_IN3|12|32|2S0_LRCK_TX/GPIO3_D2| |SPDIF/GPIO3_C0|13|33|I2S0_SDI0/GPIO3_D3| |GND|14|34|GND| |SPI3_CS/GPIO1_C2|15|35|I2S0_SDI3SDO1/GPIO3_D6| |SPI3_CLK/GPIO1_C1|16|36|2S0_SDI2SDO2/GPIO3_D5| |GND|17|37|I2S0_SDI1SDO3/GPIO3_D4| |Linux_RX|18|38|I2S0_LRCK_RX/GPIO3_D1| |Linux_TX|19|39|MCU_PA1| |3.3V|20|40|GND| [[../applications/gpio/40pin-header]]